Greasemonkey script for easy river drawing

[ispyisail]

I can't get this script to install/work in chrome, any tips

Google Chrome 18.0.1025.151 m

street to river.jpg (26.15 KiB) Viewed 1442 times

street to river 2.jpg (135.17 KiB) Viewed 1442 times

[Laakkus]

I can't get this script to install/work in chrome, any tips

Google Chrome 18.0.1025.151 m

street to river.jpg

street to river 2.jpg

You seem to be using tampermonkey? (If yes, then) stop using it and install again. That worked for me.

P.s. read the thread before posting. The answer was already there.

Sent from my GT-I9000 using Tapatalk 2 Beta-6

[ispyisail]

You seem to be using tampermonkey? (If yes, then) stop using it and install again. That worked for me.

Thanks, that fixed the install problem

The problem now is its says

road to riner 3.jpg (76.02 KiB) Viewed 1402 times

But no river is created?

[Timbones]

Have you switched on the Landmarks layer? (Shift+L) If you haven't, then it looks like the script hasn't worked.

[ispyisail]

Thanks

smacks hand against head

That was the problem

Question: the river gets smaller in width as its gets longer. can you join land marks together to create a variable width river?

[ispyisail]

This gets me grumpy

save.jpg (33.54 KiB) Viewed 1392 times

I draw a massive long river then I get this error and I have to start all over

Does any body else get this or is it just me?

[Laakkus]

This gets me grumpy

save.jpg

I draw a massive long river then I get this error and I have to start all over

Does any body else get this or is it just me?

I do. Nowadays I just draw a bit shorter "rivers" and adjust the borders. Bit annoying though. I think the problem is on Waze's side. Not the only saving problem you know..

Sent from my GT-I9000 using Tapatalk 2 Beta-6

[Timbones]

This gets me grumpy

[An error occurred while saving]

I draw a massive long river then I get this error and I have to start all over

Does any body else get this or is it just me?

I've seen this a lot, and I've tracked it down to corners where two points cross over each other. WME really doesn't like Landmarks that become twisted (kinda hard to describe).

Solution is to check the whole stretch of river, looking for pairs of geometry points that are very close together. Usually found near sharp corners of the river, and you might notice a missing point nearby. Delete one of the pair, and save. Repeat as necessary.

[Laakkus]

This gets me grumpy

[An error occurred while saving]

I draw a massive long river then I get this error and I have to start all over

Does any body else get this or is it just me?

I've seen this a lot, and I've tracked it down to corners where two points cross over each other. WME really doesn't like Landmarks that become twisted (kinda hard to describe).

Solution is to check the whole stretch of river, looking for pairs of geometry points that are very close together. Usually found near sharp corners of the river, and you might notice a missing point nearby. Delete one of the pair, and save. Repeat as necessary.

That's true although it doesn't always help. And that's when it gets really annoying. Sometimes it just won't save no matter what you try.

Sent from my GT-I9000 using Tapatalk 2 Beta-6

[DGlanem]

I want to make a Railroad-Landmark from an existing street(railroad).

The tool gives me a messagebox "there are no new streets" (or so).

A few minutes later I try it again - the messagebox say "...succsessful created..." .


Where is my Bug?


regards from germany
#Dominik