← Older revision

Revision as of 16:48, 21 May 2013

(One intermediate revision by one user not shown)

Line 64:

===Turn restrictions (allowed turns)===

−

~~{{UpdateForEditorChange}}~~

−

{{Red|Review the information on the new [[Soft_and_hard_turns|soft and hard turn restrictions]] before reviewing the information below. This section will be updated soon to reflect these changes.}}

+

====Standard Turns====

Set by selecting a segment which will allow you to see the connectivity arrows and modify these allowed turns at each end of the segment.

−

[[Image:Wme1 turn arrows horizontal.jpg]]

+

[[Image:Wme1 turn arrows horizontal.jpg|center|frame|2-way to 2-way turn arrows]]

+

A green arrow indicates that travel is allowed from the selected segment in the direction of the arrow. A red arrow with the slashed-circle icon indicates that travel is not allowed (restricted) from the selected segment in the direction of the arrow. Clicking an arrow toggles between allowed and restricted. Each arrow must be set correctly for Waze to route correctly.

−

~~A green arrow indicates that travel is allowed from~~ the ~~selected segment in~~ the ~~direction of the arrow~~. ~~A red arrow indicates that travel is not allowed (restricted) from~~ the ~~selected segment in the direction of the arrow. Clicking an arrow changes the color of the arrow. Each arrow must be set correctly for Waze to route correctly~~.

+

Where the arrows appear depends on the road. One-way roads will only have arrows at the end, and roads with unknown directionality will have no connectivity arrows at all.

−

~~The green arrow has a small checkmark and the red arrow has a small x inside the arrow~~ to ~~aid color~~-~~blind editors~~.

+

[[Image:Wme turn arrows horizontal 1x1way.jpg|center|frame|1-way to 1-way example]]

+

[[Image:Wme turn arrows horizontal 1x2way.jpg|center|frame|1-way to 2-way example]]

−

~~Where the arrows appear depends on the road. One~~-way ~~roads~~ will ~~only have arrows~~ at the ~~end~~, ~~and roads~~ with ~~unknown directionality will have no connectivity arrows at all~~.

+

====U-Turns====

+

Two-way segments will also show the small u-turn arrow icon at both ends of the segment. This is used, as its named suggests, gives control over Waze may use a segment end node as a u-turn. Just as with other turn restrictions, allowed u-turns must be set on a per-segment-per-end-node basis. This very granular control is required for quality route selection.

+

====Turn restrictions Tips====

* Press '''s''' to separate overlapping arrows.

* Press '''a''' to toggle connection arrows transparent or opaque so you can see beneath them and click items under them

← Older revision		Revision as of 18:27, 22 May 2013
(4 intermediate revisions by one user not shown)
Line 45:		Line 45:

	=== How to "Un-Split" two One-Way Roads ===		=== How to "Un-Split" two One-Way Roads ===
		+	I came here yesterday to solve a UR that would clearly be solved if I ‘Un-Split’ the road since it passed all the conditions. However, after following these instructions I ended up missing addresses on the south side of the road and had to go back and add them one-by-one….ouch.
		+
		+	After discovering what happened I found this discussion: http://www.waze.com/forum/viewtopic.php?f=8&t=48787&hilit=merge
		+
		+	This discussion has videos from bgodette and step-by-step pictures from AlanOfTheBerg.
		+
		+	As this wiki section stands right now, you will lose half of your addresses when you preform step #1 below of the Original steps.
		+
		+	Here is a step that needs to be added to the new instructions:
		+
		+	After BOTH sides are merged into one, you need to re-align house number to the street so that it lines up with driveway/entrance of the building the bubble is over.
		+	# With the street/road selected, click ‘Edit house numbers.’
		+	# After the screen changes to enable house number editing, you need to select each house number one-by-one.
		+	# With the house number selected, you will notice the dashed line is attached to the dot down the street depending on the number of segments.
		+	# Select the dot and move it back to where it should be.
		+
		+	Since the above mentioned discussion is brand-new and active, I’m not going to change this section of the wiki below until all are in agreement.
		+
		+	Original wiki instructions follow:
		+
		+
	Sorry to say it, but there is no easy way to merge two one-way roads back into a two-way road--which is why you should always give a lot of thought before splitting a road in the first place. And then think some more.		Sorry to say it, but there is no easy way to merge two one-way roads back into a two-way road--which is why you should always give a lot of thought before splitting a road in the first place. And then think some more.

waze - Changes related to "Eesti" [en]

Best map editing practice

Map Editing Quick-start Guide

@@ Line 64: / Line 64: @@
 ===Turn restrictions (allowed turns)===
 {{Red|Review the information on the new [[Soft_and_hard_turns|soft and hard turn restrictions]] before reviewing the information below. This section will be updated soon to reflect these changes.}}
 Set by selecting a segment which will allow you to see the connectivity arrows and modify these allowed turns at each end of the segment.
-[[Image:Wme1 turn arrows horizontal.jpg]]
+[[Image:Wme1 turn arrows horizontal.jpg|center|frame|2-way to 2-way turn arrows]]
-A green arrow indicates that travel is allowed from the selected segment in the direction of the arrow.  A red arrow indicates that travel is not allowed (restricted) from the selected segment in the direction of the arrow. Clicking an arrow changes the color of the arrow. Each arrow must be set correctly for Waze to route correctly.
+Where the arrows appear depends on the road. One-way roads will only have arrows at the end, and roads with unknown directionality will have no connectivity arrows at all.
-The green arrow has a small checkmark and the red arrow has a small x inside the arrow to aid color-blind editors.
+[[Image:Wme turn arrows horizontal 1x1way.jpg|center|frame|1-way to 1-way example]]
-Where the arrows appear depends on the road. One-way roads will only have arrows at the end, and roads with unknown directionality will have no connectivity arrows at all.
+====U-Turns====
 * Press '''s''' to separate overlapping arrows.
 * Press '''a''' to toggle connection arrows transparent or opaque so you can see beneath them and click items under them