What is causing this turn instruction?

The place to get information and ask questions about everything to do with properly and successfully editing the Waze Map.

Use this forum for all general editing questions, and the sub-forums for specific types of Waze Map Editor features.

Moderator: Unholy

Re: What is causing this turn instruction?

Postby AlanOfTheBerg » Wed Jun 13, 2012 3:56 pm

Looks like corrupted junctions. Disconnect the side-streets, delete the junctions. Save. Then reconnect the side streets.

Not sure how a highway just "ends" at a spot not an intersection. Roadways rarely turn from highway to street without intersecting another highway or primary street. That looks suspicious.
Wiki Resources: Map Editing Manual | alanoftheberg@gmail.com
Oregon-based US Country Manager | iPhone6 - VZ - iOS 8.2 | Waze v3.9.3.928
AlanOfTheBerg
Waze Global Champs
Waze Global Champs
 
Posts: 23166
Joined: Sat Aug 28, 2010 8:48 pm
Location: US Country Manager - Oregon, USA
Has thanked: 1029 times
Been thanked: 4165 times

Re: What is causing this turn instruction?

Postby gettingthere » Wed Jun 13, 2012 6:16 pm

trathkopf wrote:It's not really a highway. It's a road named "Hwy" and it was given the highway designation with the original map import.


Sounds like a good opportunity to correct the road classification.
Wazer in San Diego, California USA and Tijuana, Mexico
iPhone 6 Plus, iOS 8.1.3, Waze 3.9
gettingthere
Waze Global Champs
Waze Global Champs
 
Posts: 6039
Joined: Fri Nov 05, 2010 5:30 am
Location: Southern California, USA
Has thanked: 30 times
Been thanked: 169 times

What is causing this turn instruction?

Postby jetarpon » Wed Jun 13, 2012 8:49 am

This section of road has two update requests over the last few months for "turn not allowed." Each has an erroneous turn instruction in the same spot. One update request was for a westbound user, instructed to turn left, and the other was for an eastbound user, instructed to turn right. There is no road for them to turn onto.

Any idea what is causing this?

https://www.waze.com/editor/?zoom=5&lat=61.25367&lon=-149.72879&layers=BFTFTTTFTTFTTTTFTTTTFT
jetarpon
 
Posts: 5
Joined: Mon May 21, 2012 6:36 pm
Has thanked: 0 time
Been thanked: 0 time

Re: What is causing this turn instruction?

Postby jetarpon » Wed Jun 13, 2012 5:29 pm

It's not really a highway. It's a road named "Hwy" and it was given the highway designation with the original map import.

I found another "highway" yesterday that I fixed. It was a short stretch of road on the side of a mountain called "Mile Hwy," and designated a minor highway. In intersected a road called "Mile Hi Ave." Further investigation revealed that its actual name was "Mile Hi Way."
jetarpon
 
Posts: 5
Joined: Mon May 21, 2012 6:36 pm
Has thanked: 0 time
Been thanked: 0 time

Re: What is causing this turn instruction?

Postby jetarpon » Wed Jun 13, 2012 6:53 pm

Yep. I'm doing that, too. I was trying to figure out the cause of the bad instruction before I made any changes.
jetarpon
 
Posts: 5
Joined: Mon May 21, 2012 6:36 pm
Has thanked: 0 time
Been thanked: 0 time

Re: What is causing this turn instruction?

Postby Timbones » Wed Jun 13, 2012 9:19 am

It might be necessary to disconnect all the segments from the junction (so that it disappears), and then reconnect them again (to make a new one).
Timbones(6) • UK Community Coordinator • Forum Moderator • Routing Expert
Scripts: WME Colour Highlights v1.98 (Dec 2014)WME Route Tester
Timbones
Coordinators
Coordinators
 
Posts: 5094
Joined: Wed Feb 09, 2011 10:33 am
Location: York, UK
Has thanked: 471 times
Been thanked: 1563 times

Re: What is causing this turn instruction?

Postby TonyG-UK » Wed Jun 13, 2012 9:03 am

Check there aren't any geometry points right near the ends of these roads.
Image
UK Country Manager. Area manager: Wiltshire, UK
TonyG-UK
Beta tester
Beta tester
 
Posts: 530
Joined: Mon Aug 22, 2011 4:36 pm
Location: UK
Has thanked: 2 times
Been thanked: 50 times


Return to Waze Map Editor

Who is online

Users browsing this forum: matahr