[Script] WME RA Util
WME RA Util
Current Version: 2019.04.08.01
Greasyfork: https://greasyfork.org/en/scripts/23616-wme-ra-util
This script enables the ability to shift a roundabout N/E/S/W by a definable amount (default amount is 1 meter). This allows an editor to correctly place a roundabout that may be out of alignment with aerials (due to bad initial drawing, being created before aerials were updated, etc.) without needing to delete & recreate the roundabout and thus lose segment history.
It also gives the ability to rotate the roundabout - currently it is only possible to make an ellipse stretched N/S or E/W. Using this script the ellipse roundabout can be created N/S or E/W and rotated into the correct position.
Notes
The script will remember the collapsed/expanded state between loads so you can minimize it until you need to use the functionality.
It is also possible to drag the window around the screen and its last location will persist to the next load.
Change Log
2019-04-08 - 2019.04.08.01 - Shifting of nodes in RAs with differing A to B & B to A segments should now work correctly.
2019-03-27 - 2019.03.27.02 - Added the ability to shift the A & B nodes of a roundabout segment along the roundabout so it isn't necessary to disconnect and reconnect after adjusting the size/position and the node no longer lines up.
2019-03-21 - 2019.03.21.01 - Roundabout expansion/contraction now possible.
2018-02-27 - 2018.02.27.1 - Incorporated the Roundabout Angles script, including a checkbox to enable/disable. This checkbox is available on the Roundabout Utility window that is displayed when a roundabout segment is selected.
2017-11-14 - 2017.11.14.01 - Fixing the layout so both adjustment controls are on the same line
2017-02-28 - 0.3.6 - Undo should now work correctly after shifting the RA.
2016-11-22 - Added using MultiAction in order to reduce the save count bloat. Each shift/rotate should now only increase the total changes by 1 instead of 8.
Current Version: 2019.04.08.01
Greasyfork: https://greasyfork.org/en/scripts/23616-wme-ra-util
This script enables the ability to shift a roundabout N/E/S/W by a definable amount (default amount is 1 meter). This allows an editor to correctly place a roundabout that may be out of alignment with aerials (due to bad initial drawing, being created before aerials were updated, etc.) without needing to delete & recreate the roundabout and thus lose segment history.
It also gives the ability to rotate the roundabout - currently it is only possible to make an ellipse stretched N/S or E/W. Using this script the ellipse roundabout can be created N/S or E/W and rotated into the correct position.
Notes
The script will remember the collapsed/expanded state between loads so you can minimize it until you need to use the functionality.
It is also possible to drag the window around the screen and its last location will persist to the next load.
Change Log
2019-04-08 - 2019.04.08.01 - Shifting of nodes in RAs with differing A to B & B to A segments should now work correctly.
2019-03-27 - 2019.03.27.02 - Added the ability to shift the A & B nodes of a roundabout segment along the roundabout so it isn't necessary to disconnect and reconnect after adjusting the size/position and the node no longer lines up.
2019-03-21 - 2019.03.21.01 - Roundabout expansion/contraction now possible.
2018-02-27 - 2018.02.27.1 - Incorporated the Roundabout Angles script, including a checkbox to enable/disable. This checkbox is available on the Roundabout Utility window that is displayed when a roundabout segment is selected.
2017-11-14 - 2017.11.14.01 - Fixing the layout so both adjustment controls are on the same line
2017-02-28 - 0.3.6 - Undo should now work correctly after shifting the RA.
2016-11-22 - Added using MultiAction in order to reduce the save count bloat. Each shift/rotate should now only increase the total changes by 1 instead of 8.
Re: [Script] WME RA Util