Get a sneak peek at whats next for Permanent Hazards on our April 7th Office Hours!
Discussion for the unofficial, community-developed addons, extensions and scripts built for the Waze Map Editor.

The official index of these tools is the Community Plugins, Extensions and Tools wiki page.
Post by shomgoon
Thank you for good job
I use this script for a long time
Version: WME Street to River PLUS 1.0 in your link does not work in Chrome

Please help
shomgoon
Posts: 1137
Has thanked: 553 times
Been thanked: 295 times
Send a message

Post by shomgoon
Thank you very much!
I tried to install it without Tampermonkey :mrgreen:
All works perfectly
shomgoon
Posts: 1137
Has thanked: 553 times
Been thanked: 295 times
Send a message

Post by Szata76
It doesn't work for me. I'm using it with Tampermonkey and Chrome.
Does it compatible wiht the latest WME?
Szata76
Waze Global Champs
Waze Global Champs
Posts: 1711
Has thanked: 251 times
Been thanked: 479 times
Send a message

Editor level: 6;
Area: Magyarország / Hungary ● Corfu (GR)
facebook.com/waze.hu

Post by Timbones
aeytom wrote:I have uploaded a new version to userscripts.org. This new version integrates some changes from Timbones. Now you can create "railroad" landmarks with one click.
Thanks Tom!

Here's a summary of the changes:
  • separate button to do 'Street to railway'
  • default width of 8m (if not set in road name)
  • creates landmark of type 'Other'
  • will work on existing railroad segments
Timbones
Coordinators
Coordinators
Posts: 7357
Answers: 2
Has thanked: 952 times
Been thanked: 2916 times
Send a message
Timbones(6) • UK Coordinator • Forum Moderator • Closure Monitor
Scripts: WME Colour HighlightsWME Route TesterWME Geometries

Post by Timbones
Have you switched on the Landmarks layer? (Shift+L) If you haven't, then it looks like the script hasn't worked.
Timbones
Coordinators
Coordinators
Posts: 7357
Answers: 2
Has thanked: 952 times
Been thanked: 2916 times
Send a message
Timbones(6) • UK Coordinator • Forum Moderator • Closure Monitor
Scripts: WME Colour HighlightsWME Route TesterWME Geometries

Post by Timbones
ispyisail wrote:This gets me grumpy

[An error occurred while saving]

I draw a massive long river then I get this error and I have to start all over

Does any body else get this or is it just me?
I've seen this a lot, and I've tracked it down to corners where two points cross over each other. WME really doesn't like Landmarks that become twisted (kinda hard to describe).

Solution is to check the whole stretch of river, looking for pairs of geometry points that are very close together. Usually found near sharp corners of the river, and you might notice a missing point nearby. Delete one of the pair, and save. Repeat as necessary.
Timbones
Coordinators
Coordinators
Posts: 7357
Answers: 2
Has thanked: 952 times
Been thanked: 2916 times
Send a message
Timbones(6) • UK Coordinator • Forum Moderator • Closure Monitor
Scripts: WME Colour HighlightsWME Route TesterWME Geometries

Post by wroadd
Do not try to create too long landmarks, it creates "general error". It is not a script error...
wroadd
Posts: 1839
Been thanked: 4 times
Send a message
Waze Global Champ, (Re)tired
Hardware: Oukitel U22 & iPhone 7
Car: Soca Octavia : red