Get a sneak peek at whats next for Permanent Hazards on our April 7th Office Hours!
Discussion for the unofficial, community-developed addons, extensions and scripts built for the Waze Map Editor.

The official index of these tools is the Community Plugins, Extensions and Tools wiki page.
Post by irowiki
I'm just used to having all soft turns highlighted in yellow, and unneeded nodes in blue. Having soft turns in blue throws me off bigtime. I'll get used to it I guess!
irowiki
Posts: 250
Has thanked: 66 times
Been thanked: 37 times
Send a message

Post by irowiki
It is possible (but unlikely, I think) that the area you were scanning was already cleaned up.

Otherwise, try zooming in a bit and running the report again.
irowiki
Posts: 250
Has thanked: 66 times
Been thanked: 37 times
Send a message

Post by irowiki
Oh, it means click "play" to continue. (or it might be pause at that point)
irowiki
Posts: 250
Has thanked: 66 times
Been thanked: 37 times
Send a message

Post by irowiki
it is updated all the time! Just be patient, berestovskyy is a volunteer just like the rest of us!
irowiki
Posts: 250
Has thanked: 66 times
Been thanked: 37 times
Send a message

Post by irowiki
pumrum wrote:
Exit via ramps only, typically with deceleration zones.
This would highlight any time a freeway segment is connected to anything that is not a ramp or another freeway segment. This may only apply to the US, and I'm not sure how this would work in a localization pack.
In the US at least, Freeways can start and stop without ramps. I know of several interstates (I-27 in Texas, for example) that just start from a surface street and end into a surface street without any fanfare.
irowiki
Posts: 250
Has thanked: 66 times
Been thanked: 37 times
Send a message

Post by irowiki
Jay91150 wrote:
The same thing occurs in Canada - large sections of the Trans-Canada Highway near me have controlled access (ramps/interchanges) for major roads and direct connections for minor roads.

Oh yes, forgot about that. There's remote interstates in the US that have at grade intersections for farms and such.
irowiki
Posts: 250
Has thanked: 66 times
Been thanked: 37 times
Send a message

Post by ispyisail
Hi all

It appears that WME Validator 1.0.0 in auto scan mode is not picking up "Unconfirmed road (#23)" but it does in manual mode?



It may also be that I'm doing something wrong?

UPDATE:
It appears that if the unconfirmed engagement has been changed to a "two way" and or upgraded to a "Primary Street" It doesn't get detected? see screen shot

This segment works fine

ispyisail
Waze Local Champs
Waze Local Champs
Posts: 3369
Has thanked: 502 times
Been thanked: 547 times
Send a message

Post by ispyisail
sorry

https://www.waze.com/editor/?lon=168.51 ... 89&env=row

My PC is not picking up anything at this zoom level
ispyisail
Waze Local Champs
Waze Local Champs
Posts: 3369
Has thanked: 502 times
Been thanked: 547 times
Send a message

Post by ispyisail
Thanks for taking the time to look

I clicked your link then hit scan (same zoom level)

this is the result



these are my settings











Thanks
ispyisail
Waze Local Champs
Waze Local Champs
Posts: 3369
Has thanked: 502 times
Been thanked: 547 times
Send a message

Post by ispyisail
berestovskyy wrote:Click Settings->Reset Defaults or select "search" tab and then clear the "Updated by" field. Your report does not include segments updated by you:
ispyisail wrote:
Sorry and Thanks

you are correct, I feel very silly

Must have been like this for some time :(

Thanks again
ispyisail
Waze Local Champs
Waze Local Champs
Posts: 3369
Has thanked: 502 times
Been thanked: 547 times
Send a message